| Specification: |
|
External Sensor Connector: |
|
|
Type |
| 6 pin Switchcraft Plug (EN3C6M
) |
| Weatherproof |
| IP66 |
|
|
|
Pinout |
| 1 Switched Reference voltage |
| 2 First Analog Input |
| 3 Second Analog Input |
| 4 Third Analog Input |
| 5 Fast Pulse Input |
| 6 Common Ground |
 |
View from Front of Socket or Rear of Plug |
|
|
Three Analogue Channels: |
|
|
To log any
combination of: |
| Temperature |
Wind Direction |
| Humidity |
Soil Moisture Tension |
| Pressure |
Leaf Wetness |
| Light |
Voltage (DC) |
| Solar Energy |
Current (DC) |
|
|
|
 The three analog channels have identical
characteristics. Each channel can operate in two modes, Absolute and Ratiometric. The mode
of operation is determined by the probe type selected for that channel. The probe type is
selected using the Channel and Probe Setup Tab of the Logger Control Screen in the Omnilog
Software. Using this software, a different Probe can be selected for each Channel.
Temperature (Thermister) , Pressure and Humidity probes are typically Ratiometric. Voltage
and current inputs are Absolute.
|
|
|
| Maximum readable input voltage in Ratiometric
mode |
3.3 Volts Nominal (see note) |
| Maximum readable input voltage in Absolute
mode |
2.048Volts |
| Maximum voltage input without damaging logger |
5 Volts |
| Maximum current to be drawn by the combination
of all three probes |
5mA |
| Input Leakage Current |
0.1uA |
|
|
|
Note:The maximum readable voltage in ratiometric mode should be
derived from the logger supply (Pin 1) and will therefore decrease over the life of the
battery to a minimum of 2.7 Volts.
|
|
|
|
|
|
One Fast Pulse Digital Channel |
|
|
To log: |
| Rainfall |
| Wind speed |
| Counter (up to 65535) |
| Flow |
| Frequency (up to 60 kHz) |
|
|
|
The fast pulse input can be used in two modes,
Counter or Frequency.
Counter mode is used for functions such as rainfall. Frequency Mode is
used for wind speed or flow sensors. The mode of operation is determined by the
probe type selected for that channel. The probe type is selected using the Channel and
Probe Setup Tab of the Logger Control Screen in the Omnilog Software.
|
|
|
| Maximum Count Per Logging Period |
65535 |
| Maximum Frequency with logging period set to
1sec |
60kHz |
| Preferred Switch Input Type |
Normally Open |
| Preferred Digital Input Type |
Normally High |
| Minimum High Period |
1uSec |
| Mininum Low Period |
1uSec |
| Input Impedence |
470 kOhm |
| Prefered voltage input |
3.3 Volts |
| Maximum voltage input |
5.0 Volts |
|
|
|
|
|
|
Internal Temperature: |
|
|
Sensor Type |
Thermister |
|
|
Linear accuracy over range |
±0.3ºC (0ºC to 70ºC) |
|
|
Repeatability |
±0.1ºC |
|
|
Long term stability |
±0.1ºC |
|
|
|
|
|
Logger: |
|
|
Working Temperature |
-30ºC to +70ºC |
|
|
Storage Temperature |
-30ºC to +70ºC |
|
|
Sampling Rate |
| 1 second minimum |
| 10 hours maxium |
| in 1 second intervals |
|
|
|
Storage
capacity |
| Logging one channel |
| 522,240 samples |
| 362 days with 1 min logging interval |
| 4.9 years with 5 min logging interval |
| Logging two channels |
| 261,120 samples |
| 181 days with 1 min logging interval |
| 2.4 years with 5 min logging interval |
| Logging three channels |
| 174,080 samples |
| 120 days with 1 min logging interval |
| 1.6 years with 5 min logging interval |
| Logging four channels |
| 130,560 samples |
| 90 days with 1 min logging interval |
| 1.2 years with 5 min logging interval |
|
|
|
Alarms |
| Two independent Alarms |
| Triggered on any combination of six user configurable
Alarm Conditions |
| Both alarms can be configured to send SMS messages |
| Alarms can be reset on user configurable Reset Conditions |
| Alarms can be visually checked using the Omnilog Software |
|
|
|
Start modes |
| Start immediately |
| Start on date/time |
| Start on condition (eg temperature > 20°C) |
| Start on trigger (push button on logger) |
|
|
|
Stop modes |
| Stop when memory is full |
| Stop on date/time |
| Loop around (continues logging) |
|
|
|
Logging
Modes |
| Each channel can be set to log any combination of: |
- Point readings
- Average reading
- Maximum reading
- Minimum reading
|
|
|
|
Battery |
| User Replaceable |
| Custom 7.2V Lithium battery pack |
| One to Five years depending on usage. |
| The data is retained in the case of battery failure. |
| Battery Status Monitor in OmniLog Software |
|
|
|
Download Time |
9 minutes 30 seconds for Full
Logger |
|
|
Case material |
304 Stainless tube |
|
|
Screw on end cap |
Plated brass |
|
|
Weight |
149g |
|
|
Size |
20mm diameter X 185mm long |
|
Standard Probe Sets: |
|
|
1
External Temperature |
|
|
2
External Temperature |
|
|
3
External Temperature |
|
|
Humidity
& Temperature Probe |
|
|
Pressure
Probe |
|
|
Pressure
with additional Temperature Probe |
|
|
Light
/ Solar EnergyProbe |
|
|
Light
/ Solar EnergyProbe with additional Temperature Probe |
|
|
Rain
Gauge Adaptor |
|
|
Rain
Gauge Adaptor with additional Temperature Probe |
|
|
Wind
Speed Anemometer |
|
|
Wind
Speed Anemometer with Temperature Probe |
|
|
Leaf
Wetness Probe |
|
|
Leaf
Wetness Probe with additional Temperature Probe |
|
|
3
input 4 to 20mA adaptor |
